BS EN 1337-5-2005 Structural bearings-Part 5 Pot bearings
|
ID： |
FCE5A31C9AEC43589166BA9246DF4F34 |
|
文件大小(MB)： |
0.55 |
|
页数： |
60 |
|
文件格式： |
|
|
日期： |
2010-8-10 |
|
购买： |
文本摘录（文本识别可能有误，但文件阅览显示及打印正常，pdf文件可进行文字搜索定位）：
BRITISH STANDARD BS EN,1337-5:2005,Structural bearings —,Part 5: Pot bearings,The European Standard EN 1337-5:2005 has the status of a,British Standard,ICS 91.010.30, , , ,BS EN 1337-5:2005,This British Standard was,published under the authority,of the Standards Policy and,Strategy Committee,on 29 December 2006,. BSI 2006,ISBN 0 580 49851 4,National foreword,This British Standard was published by BSI. It is the UK implementation of,EN 1337-5:2005. It partially supersedes BS 5400-9-1:1983 and,BS 5400-9-2:1983 which will remain current until the remaining parts of the,BS EN 1337 series have been published, the last part being Part 8.,The UK participation in its preparation was entrusted to Technical Committee,B/522, Structural bearings.,A list of organizations represented on B/522 can be obtained on request to its,secretary.,This publication does not purport to include all the necessary provisions of a,contract. Users are responsible for its correct application.,Compliance with a British Standard cannot confer immunity from,legal obligations.,Amendments issued since publication,Amd. No. Date Comments,EUROPEAN STANDARD,NORME EUROPéENNE,EUROP腎SCHE NORM,EN 1337-5,March 2005,ICS 91.010.30,English version,Structural bearings - Part 5: Pot bearings,Appareils d'appui structuraux - Partie 5: Appareils d'appui à,pot,Lager im Bauwesen - Teil 5: Topflager,This European Standard was approved by CEN on 4 June 2004.,CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European,Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national,standards may be obtained on application to the Central Secretariat or to any CEN member.,This European Standard exists in three official versions (English, French, German). A version in any other language made by translation,under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official,versions.,CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,Slovenia, Spain, Sweden, Switzerland and United Kingdom.,EUROPEAN COMMITTEE FOR STANDARDIZATION,COMITé EUROPéEN DE NORMALISATION,EUROP腎SCHES KOMITEE FüR NORMUNG,Management Centre: rue de Stassart, 36 B-1050 Brussels,. 2005 CEN All rights of exploitation in any form and by any means reserved,worldwide for CEN national Members.,Ref. No. EN 1337-5:2005: E,EN 1337-5:2005 (E),2,Contents page,Foreword 3,1 Scope.. 4,2 Normative references 4,3 Terms, definitions, symbols and abbreviations .. 5,4 Functional requirements . 9,5 Materials 9,6 Design requirements .. 10,7 Manufacturing assembly and tolerances .. 20,8 Conformity evaluation 21,9 Installation 22,10 In-service inspection .. 22,Annex A (normative) Internal seals 24,Annex B (informative) Determination of compression stiffness 29,Annex C (informative) Factory Production Control (FPC) .. 30,Annex D (normative) Determination of restraint moment 33,Annex E (normative) Long term rotation and load test. 37,Annex F (normative) Test equipment 41,Annex G (informative) Application of internal seals .. 43,Annex ZA (informative) Clauses of this European Standard addressing the provisions of,the EU Construction Products Directive 44,Bibliography . 56,EN 1337-5:2005 (E),3,Foreword,This document (EN 1337-5:2005) has been prepared by Technical Committee CEN/TC 167,“Structural bearings”, the secretariat of which is held by UNI.,This European Standard shall be given the status of a national standard, either by publication of an,identical text or by endorsement, at the latest by December 2006, and conflicting national standards,shall be withdrawn at the latest by December 2006.,This document has been prepared under a mandate given to CEN by the European Commission and,the European Free Trade Association, and supports essential requirements of EU Directive (s).,For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this,document.,The European Standard EN 1337 consists of the following 11 parts:,Part 1 General design rules,Part 2 Sliding elements,Part 3 Elastomeric bearings,Part 4 Roller bearings,Part 5 Pot bearings,Part 6 Rocker bearings,Part 7 Spherical and cylindrical PTFE bearings,Part 8 Guide bearings and restrain bearings,Part 9 Protection,Part 10 In……
……